Contact Us

Fax:+86-571-88220227

Mail:[email protected]

Add:No. 2, Longshen Cdc, Sandun Town, Hangzhou, Zhejiang, China

Worm Drive Servo

Worm Drive Servo

This gearbox utilizes a 30:1 ratio worm-drive reduction for applications that require extremely slow and smooth rotational motion. The worm-drive design not only minimizes backlash but also eliminates back-driving the gearmotor so a position can be held even when power is not applied. The...

Inquiry

  • Product Details

Servo worm gear units have three types : 45 - 50 - 55 - 63 - 75 - 90 ,with dual lead worm drive.Left and right flank of worm shaft using different lead angle,causing tooth thickness gradual change,So that you can move worm shaft and adjust backlash.

This gearbox utilizes a 30:1 ratio worm-drive reduction for applications that require extremely slow and smooth rotational motion. The worm-drive design not only minimizes backlash but also eliminates back-driving the gearmotor so a position can be held even when power is not applied.

The precision ground 3/8” stainless steel output shaft is supported by dual 3/8” ABEC 5 ball bearings to support a load from any orientation. The ¼” ABS plastic and aluminum structure provides a rigid framework without adding unnecessary weight and is easily mounted to any flat surface by utilizing the base mounting tabs. Our Standard Spur Gear motors will work with this gearbox (motor sold separately).

The Vertical Shaft Worm-Drive Gearbox is perfect for turn-tables, time-lapse systems and low-speed applications that require high precision and torque.

Motor RPM required = 1 / (minutes per rotation desired / 30)

Example: 1 / (10 minutes per rotation / 30) = 3 RPM motor needed to achieve 10 minutes per rotation (at max speed)

1Low backlash right angle servo worm reducer

low backlash reducer china

Low rotation Make choice :

The following headings contain information on essential elements for selection and correct use of gearbox.
For specific data on the gearbox range,see the relevant chapters.
OUTPUT TORQUE
1、Rated output torque
Mn2 [Nm]
The torque that can be transmitted continuously through the output shaft, with the gear unit operated under a service factor fs = 1.
2、Required torque
Mr2 [Nm]
The torque demand based on application requirement. It is recommended to be equal to or less than torque Mn2 the gearbox under study is rated for.
3、Calculated torque
Mc2 [Nm]
Computational torque value to be used when selecting the gearbox. It is calculated considering the required torque Mr2 and service factor fs, as per the relationship here after:
POWER
1、Rated input power
Pn1 [kW]
The parameter can be found in the gearbox rating charts and represents the KW that can be safely transmitted to the gearbox, based on input speed n1 and service factor fs= 1.
2、Rated output power
Pn2 [kW]
This value is the power transmitted at gearbox output. it can be calculated with the following formulas:
EFFICIENCY
Efficiency is a parameter which has a major influence on the sizing of certain applications, and basically depends on gear pair designelements.
The mesh data table on page 9 shows dynamic efficiency (n1=1400)and static efficiency values.
Remember that these values are only achieved after the unit has been run in and is at the working temperature.
1、Dynamic efficiency
[ηd]
The dynamic efficiency is the relationship of power delivered at output shaft P2 to power applied at input shaft P1:
2、Static efficiency
[ηs]
Efficiency obtained at start-up of the gearbox. Although this is generally not significant factor for helical gears, it may be instead critical when selecting worm gearmotors operating under intermittent duty.
SERVICE FACTOR [ fs ]
The service factor (fs ) depends on the operating conditions the gearbox is subjected to the parameters that need to be taken into consideration to select the most adequate servies factor correctly comprise:
1. type of load of the operated machine : A - B - C
2. length of daily operating time: hours/day(△)
3. start-up frequency: starts/hour (*)
TYPE OF LOAD: A - uniform, fa≤0.3
B - moderate shocks, fa≤3
C - heavy shocks, fa≤10
fa=Je/Jm
--Je(kgm2) moment of the external inertia reduced at the drive shaft
--Jm(kgm2) moment of inertia of motor
--If fa>10 please contact our Technical Service
A -Screw feeders for light materials, fans, assembly lines, conveyor belts for light materials, small mixers, lifts, cleaning machines, fillers, control machines.
B -Winding devices, woodworking machine feeders, goods lifts, balancers,threading machines, medium mixers, conveyor belts for heavy materials,winches, sliding doors, fertilizer scrapers, packing machines, concrete mixers, crane mechanisms, milling cutters, folding machines, gear pumps.
C -Mixers for heavy materials, shears, presses, centrifuges, rotating supports, winches and lifts for heavy materials, grinding lathes, stone mills, bucket elevators, drilling machines, hammer mills, cam presses, folding machines, turntables, tumbling barrels, vibrators, shredders


low backlash reducer chinalow backlash reducer chinalow backlash reducer china

Hot Tags: worm drive servo, China, suppliers, manufacturers, factory, wholesale, buy, made in China
  • Feedback
contactus